题目
示波器说明书?
19.NORM/INVERT
Selects CHI operating in normal or inverted form,this combined with I+Ⅱ can operate add or subtract for input signals.
20.C.T.
C.T.is the abbreviation of component test,it is an application of oscilloscope for testing FET.Transistor.Diode,Zener,Inductor,Capacitor etc.which are in working or damaged.
On this oscilloscope the tested component is connected in component test jacks(5),press C.T.button,the trace on CRT oftested component should be displayed the characteristic trace of components are listed in appendix.
21.TIME/DIV
Has 20 steps which ranges are form 0.2 sec/div to 0.1us/div in1:2:5 sequence.
22.X-Y
Pressing the X-Y button apply the vertical signal to the CHI or Y input connector and the horizontal signal to the CHⅡ or X input connector and the positioning on the screen can been vertically controlled by CHI position control knob.
23.HOLD OFF
Provides controls of hold off time between sweep signals to
obtain stable display when triggering an aperiodic signal.The control hold off time ranges is form 1 to 10 times of timebase.
24.VAR
1.Provides continuously variable sweep rate by a factor of 2.5.
2.Light is turned on when VAR is not at cal position.
25.X-POS(PULL*10)
1.Posotions the display horizontally.
2.pull 10:increases the dispalyed sweep rate by a factor of 10.
26.CALIBRATION(CAL)
Provides about 1 KHZ 0.2V square wave to calibrate probe frequency compensation.
27.SINGLE
Provides single sweep function after a sweep is displayed,further sweeps can't be presented until reset button is pressed again,during sweep is triggered.
28.RESET:(Reference item27)
1.In single sweep wwaiting for a coming sweep and sweep is triggered,pressed reset button to obtain a single sweep.
2.An LED located above reset button indicate single sweep is operating.
29.EXT TRIG
Form the connector the outside signal can be input whih is taken for a taken for a trigger signal.
30.TRIG SELECTOR
1.I:A sample of the signal derived form the CH1 input connector is used as a trig signal.
2.Ⅱ:A sample of the signal derived from the CHⅡ input connector is used as a trig signal.
3.I/Ⅱ:Alternative trigger which can triggter I and Ⅱ alternatively.The function is used in alternative dual trace of vertical mode operation.
4.EXT:Trigger signal is obtained form EXT TRIG connector.
31.TRIG COUPLE
1.AC-Rejects dc and attenuates signal about 100HZ,accepts signals above 100HZ.
2.LF-Accepts signals below about 10HZ.
3.HF-Accepts signals above 10HZ.
4,DC-Accepts all trigger siganls form DC to 20MHZ or greater.
不要用软件翻译的.此问题为19-31
19.NORM/INVERT
Selects CHI operating in normal or inverted form,this combined with I+Ⅱ can operate add or subtract for input signals.
20.C.T.
C.T.is the abbreviation of component test,it is an application of oscilloscope for testing FET.Transistor.Diode,Zener,Inductor,Capacitor etc.which are in working or damaged.
On this oscilloscope the tested component is connected in component test jacks(5),press C.T.button,the trace on CRT oftested component should be displayed the characteristic trace of components are listed in appendix.
21.TIME/DIV
Has 20 steps which ranges are form 0.2 sec/div to 0.1us/div in1:2:5 sequence.
22.X-Y
Pressing the X-Y button apply the vertical signal to the CHI or Y input connector and the horizontal signal to the CHⅡ or X input connector and the positioning on the screen can been vertically controlled by CHI position control knob.
23.HOLD OFF
Provides controls of hold off time between sweep signals to
obtain stable display when triggering an aperiodic signal.The control hold off time ranges is form 1 to 10 times of timebase.
24.VAR
1.Provides continuously variable sweep rate by a factor of 2.5.
2.Light is turned on when VAR is not at cal position.
25.X-POS(PULL*10)
1.Posotions the display horizontally.
2.pull 10:increases the dispalyed sweep rate by a factor of 10.
26.CALIBRATION(CAL)
Provides about 1 KHZ 0.2V square wave to calibrate probe frequency compensation.
27.SINGLE
Provides single sweep function after a sweep is displayed,further sweeps can't be presented until reset button is pressed again,during sweep is triggered.
28.RESET:(Reference item27)
1.In single sweep wwaiting for a coming sweep and sweep is triggered,pressed reset button to obtain a single sweep.
2.An LED located above reset button indicate single sweep is operating.
29.EXT TRIG
Form the connector the outside signal can be input whih is taken for a taken for a trigger signal.
30.TRIG SELECTOR
1.I:A sample of the signal derived form the CH1 input connector is used as a trig signal.
2.Ⅱ:A sample of the signal derived from the CHⅡ input connector is used as a trig signal.
3.I/Ⅱ:Alternative trigger which can triggter I and Ⅱ alternatively.The function is used in alternative dual trace of vertical mode operation.
4.EXT:Trigger signal is obtained form EXT TRIG connector.
31.TRIG COUPLE
1.AC-Rejects dc and attenuates signal about 100HZ,accepts signals above 100HZ.
2.LF-Accepts signals below about 10HZ.
3.HF-Accepts signals above 10HZ.
4,DC-Accepts all trigger siganls form DC to 20MHZ or greater.
不要用软件翻译的.此问题为19-31
提问时间:2021-04-01
答案
太长了,19.NORM/INVERTSelects CHI operating in normal or inverted form,this combined with I+Ⅱ can operate add or subtract for input signals.正常/倒置选择通道I以正常形式还是倒置形式工作,这与I+II相结合...
举一反三
我想写一篇关于奥巴马的演讲的文章,写哪一篇好呢?为什么好
奥巴马演讲不用看稿子.为什么中国领导演讲要看?
想找英语初三上学期的首字母填空练习……
英语翻译
1,人们染上烟瘾,最终因吸烟使自己丧命.
最新试题
- 1比较碳酸钠和碳酸氢钠的酸碱性?为什么?
- 2由Na,O,H,S四种元素中的一种或几种元素组成的所有物质中,与硫酸氢钠反应的有哪些物质?
- 3牛郎织女故事中天河代表什么
- 4离地球最近的星星是哪一个
- 5用下列词语写一段话 五月 感恩 母亲 爱 哺育之情 最少用一种修辞 90字左右
- 6简述文化与政治、经济之间的关系.答案要分成1)、2)、3).这种的样的
- 715分之11、12分之7、8分之13、7分之5、9分之4从小到大排列
- 8英语中的一个句子 是连词成句
- 9已知函数f(x)=3sin(wx+Q)对任意的x都有f(π/3+x)=f(π/3-x),则f(π/3)=?
- 10已知p(a)=0.8,p(b)=0.7,证明p(ab)≥0.5
热门考点
- 1地球的内部圈层 地壳中主要的化学元素,岩石和矿物
- 2汽车紧急刹车,从开始刹到停止,轮胎在地面留下14米的擦痕,轮胎与路面动磨擦因数为0.7,g为10,1...
- 3植树节,四年级植树82,五年级植树90,六年级植树比四五年级植树的总数少54.
- 4A球由高楼顶自由落下,娄它下落高度为5m时,另一B球在离楼顶15m处自由下落,两球同时落地.求:(1)B?F
- 5已知A(-7,0)B(7,0)C(2,-12),以C为一个焦点作过A,B的椭圆,椭圆的另一个焦点的轨迹方程?要求具体过程.
- 6八大行星哪个最合适太空移民
- 7美味小吃作文,求教!
- 8若小唐同学掷出的铅球在场地上砸出一个直径约为10cm、深约为2cm的小坑,则该铅球的直径约为_cm.
- 91到100的质数加2任然是质数
- 10用二元一次方程组解决这道题.